Apparatus for thermal conductivity measurement of thin samples

Back to overview

THISYS offers an accurate, fast and uncomplicated measurement of the thermal conductivity of thin samples of high thermal conductivity materials. Typical samples are sheet materials of metals, alloys and high conductivity plastics with various filler materials. Metal samples are ideally in the thickness range of 0.1 mm or less, plastic samples typically in the thickness range of 6 mm, composites in between. THISYS is a combination of a Thin Sample Instrument (THI01) and a Measurement and Control Unit (MCU). The measurement essentially determines the temperature gradient across the sample when it is heated, in the plane of the sample itself. Employing a specially designed high accuracy thermopile sensor THI01 can handle thin sample materials (less than 0.01 to 6 mm) usually in the thermal conductivity range to 200 W/mK. Following this method, problems with contact resistance are avoided. The method is a good alternative when procedures according to ASTM D5470 are failing. Using a climate chamber a large temperature range can be covered, performing measurements at regular intervals. THISYS is fully PC controlled. For use with low thermal conductivity materials a different model, type THASYS, is available.


The measurement of thin materials with relatively high thermal conductivity is a classic problem. Commonly used methods like ASTM D 5470 - 01 (Standard Test Method for Thermal Transmission Properties of Thin Thermally Conductive Solid Electrical Insulation Materials) have shown to be highly sensitive to contact resistance, and not applicable with high conductivity materials. THISYS offers a solution to this problem.

THISYS essentially measures the temperature gradient from centre to side across the sample when mounted across a well insulated cavity, and heated with a known uniform flux.

By measuring the flux φ (derived from heater power), the differential temperature across the samples, ΔT,amp, and the sample thickness, H, it is straightforward to calculate the relative thermal conductivity λ,rel:

λ,rel ~ φ / H ΔT,amp

The measurement is performed relative to a known reference material.

THI01 design

The Hukseflux THI01 employs two aluminium "heat sinks". Each of these contains a heater that is mounted over an air-filled, insulating cavity. The sample is installed over the cavities. The resulting temperature gradient (centre-edge) is measured. Apart from the new design, the technological novelties are a thin thermocouple thermopile (proprietary Hukseflux design) performing an accurate and ultra-sensitive differential ΔT measurement, and the fact that the measurement is performed in a bath of glycerol. The THI01 can handle samples of less than 0.01 to 6 mm thickness. Samples typically are sheet materials with a size of 70 by 100 mm. The reference material is 5 mm Pyrex 7740 material. The thermal conductivity in the sheet plane, H.λ, is around 4 10-3 m2K/W. Samples ideally have values of H.λ close to that. The measurement essentially is done at the temperature of the THI01. If necessary the temperature can be changed by putting the whole THI01 in a climate chamber, performing measurements while the instrument temperature changes across the required range. In a simplified description, the measurement consists of a heating cycle and a measurement to establish ΔT. The THI01 temperature is monitored by a Pt100 temperature sensor to correct for the temperature dependence of the thermopile sensitivity.

MCU01 design

The MCU performs the functions of measurement and control as well as data storage. It is PC operated. Software in a Windows environment is part of the delivery. The parameters cycle time, sample thickness and heater area are entered and the experiment is started from the screen.


Depending on the samples to be analysed, various reference samples can be offered. Typically Pyrex 7740 is used. The Pyrex sample thermal conductivity is traceable to NPL. THISYS is suitable for use by ISO certified laboratories.

Suggested use

  • High thermal conductivity sheet materials
  • Metal alloys
  • High thermal conductivity composite materials

More information

  • Please consult the manual for a full list of THI01 specifications. This manual is available free of charge as a PDF file via e-mail. For use with low thermal conductivity materials the model THASYS is available.


Similar products


Thin Heater Apparatus for thermal conductivity measurement

Are you interested in one of our products?

Are you interested in using one of our products and do you still have some questions open?

Or would you like to get a quote?

Get a quote